Legutóbb keresett

    Hibakereső, típus:(Fejlesztői készlet), JTAG, SWD, PDI, TPI, aWire, SPI, debugWIRE, UPDI, használható:(SAM, AVR

    RS raktári szám:
    130-6124
    Gyártó cikkszáma:
    ATATMEL-ICE-PCBA
    Gyártó:
    Microchip
    Microchip
    Kategória megtekintése
    17 Raktáron van 1 munkanapon belüli szállításra.
    Add to Basket
    egység

    Hozzáadva

    Ár Darab

    37 054 Ft

    (ÁFA nélkül)

    47 059 Ft

    (ÁFÁ-val)

    egységPer unit
    1 +37 054 Ft
    RS raktári szám:
    130-6124
    Gyártó cikkszáma:
    ATATMEL-ICE-PCBA
    Gyártó:
    Microchip

    Műszaki referencia


    Engedélyezés és megfelelőség


    Termékadatok

    ATATMEL-ICE PCBA


    The Atmel-ICE series consists of development tools for debugging and programming ARM Cortex-M based Atmel SAM and Atmel AVR microcontrollers with on-chip debug capability. The Atmel-ICE series supports JTAG, SWD, PDI, TPI, aWire, SPI and debugWIRE interfaces and is compatible with Atmel Studio.

    Kit Contains:


    • Atmel-ICE unit without plastic encapsulation

    130-6122 Full Kit available

    130-6123 Basic Kit available

    System Requirements


    The Atmel-ICE unit requires that a front-end debugging environment Atmel Studio version 6.2 or later is installed on your computer. The Atmel-ICE should be connected to the host computer using the USB cable provided, or a certified Micro-USB cable.

    How to turn the Atmel - ICE on?

    The Atmel-ICE is powered by the USB bus voltage. It requires less than 100mA to operate, and can, therefore, be powered through a USB hub. The power LED will illuminate when the unit is plugged in. When not connected in an active programming or debugging session, the unit will enter low-power consumption mode to preserve your computer's battery. The Atmel-ICE cannot be powered down - it should be unplugged when not in use.

    How does it connect?

    The Atmel-ICE communicates primarily using a standard HID interface and does not require a special driver on the host computer. The Atmel-ICE must be connected to an available USB port on the host computer using the USB cable provided, or suitable USB certified micro cable. The Atmel-ICE contains a USB 2.0 compliant controller and can operate in both full-speed and high-speed modes. For best results, connect the Atmel-ICE directly to a USB 2.0 compliant high-speed hub on the host computer using the cable provided.

    Készlet típusa


    Kábelkészlet: 177-9591
    Adapterkészlet: 177-9590
    Alapkészlet: 130-6123
    PCBA készlet: 130-6124
    Teljes készlet: 130-6122


    Jellemzők

    TulajdonságÉrték
    Tartozék típusaFejlesztői készlet
    A következőkkel való használatraSAM,AVR mikrovezérlők
    CsatolóJTAG, SWD, PDI, TPI, aWire, SPI, debugWIRE, UPDI
    Programozó neveAtmel-ICE
    17 Raktáron van 1 munkanapon belüli szállításra.
    Add to Basket
    egység

    Hozzáadva

    Ár Darab

    37 054 Ft

    (ÁFA nélkül)

    47 059 Ft

    (ÁFÁ-val)

    egységPer unit
    1 +37 054 Ft